Clarity C35 User's Guide

User GuideESPAÑOLFRANÇAISENGLISHAmplifi ed TelephoneC35™

10M1M2M5M6M7M8M9M10M11M3M41Connecting your Telephone1. Carefully remove your telephone from its box. If there is any visible damage, do not attem

11GETTING STARTED3. Set the TONE/PULSE switch located on the right side of the base to correct dialing mode. Please check with your local tel

12GETTING STARTED4. Plug the fl at telephone line cord into the wall plate jack, then align the mounting bracket’s keyhole slots with the wall

13Figure 9TELEPHONE OPERATIONSPlacing a Call1. Lift the handset and dial the number you wish to call.2. Press the BOOST button and turn the Clarit

14TELEPHONE OPERATIONSDialing a Memory Location1. Pick up the handset.2. Press the memory button where the desired number has been stored.3.

15extension phone.NOTIFICATION OPTIONSRinger VolumeRinger Volume can be set to one of three (3) positions by pressing the RINGER VOLUME UP or DOWN swi

16BOOSTVOLUMEPHONE INDICATOR LIGHTSHOLD Indicator LightThis light will illuminate when the phone call is put on HOLD. To take off of HOLD, press the

17TROUBLESHOOTINGNo Dial Tone/Phone Will Not Operate1. Check all phone cords and connections. Make sure they are plugged in securely.2. Plug

18TROUBLESHOOTINGUnable To Hear Phone Ringer1. Too many phone or phone devices on a line may cause your phone to not ring. Disconnect one (1) or t

19Unable to Access Automated SystemsAutomated systems used by banks, long distance voice mail and other ap-plications require that a phone be set to “

TABLE OF CONTENTSIntroduction ...3Parts Checklist ...

20SAVE THESE INSTRUCTIONSIMPORTANT SAFETY INSTRUCTIONSWhen using your telephone equipment, basic safety precautions should always be followed to reduc

21IMPORTANT SAFETY INSTRUCTIONS operate normally by following the operating instructions. Adjust only those controls that are covered

22Part 68 of FCC Rules Informationa) This equipment complies with Part 68 of the FCC rules and the require-ments adopted by the ACTA. On the bottom of

23REGULATORY COMPLIANCEi) If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this tele-phone

24Industry Canada Technical Specifi cationsThis product meets the applicable Industry Canada technical specifi cations.Before installing this equipment,

25WARRANTY & SERVICEThe following warranty and service information applies only to products purchased and used in the U.S. and Canada. For warrant

26How to Obtain Warranty ServiceTo obtain warranty service, please prepay shipment and return the unit to the appropriate facility listed below. In th

Thank you for purchasing the Clarity C35 Amplifi ed Telephone.Operating Instructions and the associated Quick Reference Guide will provide you with the

4CONTENTS & PARTS CHECKLISTMounting bracketTelephone line cordHandset coil cordHandset Base unitBOOSTVOLUMEUser guide4 AA batteries

5C35Quick Reference GuideFEATURES 1 Phone Number Directory 2 Memory Button 3 Redial Button 4 Flash Button 5 Volume Slider 6 Low Battery Indic

6DIALPTOff LoC35Quick Reference GuideFEATURES 1 Ringer Volume Switch 2 Pulse/Tone Switch 3 Phone Line Connection1LINESIDE VIEWBACK VIEW23

7HOW TO CONNECT THE C35 PHONE FOR DESKTOP USEC35Quick Reference Guide1. Install the 4 AA batteries.2. Connect one end of the telephone line cord to

8BOOSTVOLUMEFigure A INTRODUCTION TO CLARITY POWERClarity Power™ TechnologyClarity Power not only makes calls louder, but also easier to understan

9GETTING STARTEDThere are four initial steps involved in setting up your C351. Insert four AA alkaline batteries for maximum amplifi - cation. See b